supply frequency | 50/60 Hz +/- 5 % | |
---|
connector type | 1 RJ45 on front face)Modbus | |
---|
physical interface | 2-wire RS 485 Modbus | |
---|
transmission frame | RTU Modbus | |
---|
transmission rate | 4800 bit/s9600 bit/s19200 bit/s38400 bit/s | |
---|
number of addresses | 1…247 Modbus | |
---|
communication service | Read holding registers (03) 29 wordsWrite single register (06) 29 wordsWrite multiple registers (16) 27 wordsRead/write multiple registers (23) 4/4 wordsRead device identification (43) | |
---|
prospective line Isc | 1 kA | |
---|
continuous output current | 1,4 A 4 kHz | |
---|
maximum transient current | 2,1 A 60 s | |
---|
speed drive output frequency | 0,5…400 Hz | |
---|
nominal switching frequency | 4 kHz | |
---|
switching frequency | 2...16 kHz adjustable4...16 kHz with derating factor | |
---|
braking torque | Up to 70 % of nominal motor torque without braking resistor | |
---|
motor slip compensation | AdjustablePreset in factory | |
---|
output voltage | 200...240 V 3 phases | |
---|
electrical connection | Terminal 3.5 mm², AWG 12 L1, L2, L3, U, V, W, PA, PC) | |
---|
tightening torque | 0,8 N.m | |
---|
insulation | Electrical between power and control | |
---|
supply | Internal supply for reference potentiometer 5 V DC 4,75…5,25 V), <10 mA overload and short-circuit protectionInternal supply for logic inputs 24 V DC 20,4…28,8 V), <100 mA overload and short-circuit protection | |
---|
analogue input number | 1 | |
---|
analogue input type | Configurable current AI1 0...20 mA 250 OhmConfigurable voltage AI1 0...10 V 30 kOhmConfigurable voltage AI1 0...5 V 30 kOhm | |
---|
discrete input number | 4 | |
---|
discrete input type | Programmable LI1...LI4 24 V 18...30 V | |
---|
discrete input logic | Negative logic (sink), > 16 V, < 10 V 3.5 kOhmPositive logic (source), 0...< 5 V, > 11 V | |
---|
sampling duration | 20 ms +/- 1 ms logic input10 ms analogue input | |
---|
linearity error | +/- 0.3 % of maximum value analogue input | |
---|
analogue output number | 1 | |
---|
analogue output type | AO1 software-configurable voltage 0...10 V 470 Ohm 8 bitsAO1 software-configurable current 0...20 mA 800 Ohm 8 bits | |
---|
discrete output number | 2 | |
---|
discrete output type | Logic output LO+, LO-Protected relay output R1A, R1B, R1C 1 C/O | |
---|
minimum switching current | 5 mA 24 V DC logic relay | |
---|
maximum switching current | 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay | |
---|
acceleration and deceleration ramps | SULinear from 0 to 999.9 s | |
---|
braking to standstill | By DC injection, <30 s | |
---|
protection type | Line supply overvoltageLine supply undervoltageOvercurrent between output phases and earthOverheating protectionShort-circuit between motor phasesAgainst input phase loss in three-phaseThermal motor protection via the drive by continuous calculation of I²t | |
---|
frequency resolution | Analog input converter A/D, 10 bitsDisplay unit 0.1 Hz | |
---|
time constant | 20 ms +/- 1 ms for reference change | |
---|
marking | CE | |
---|
operating position | Vertical +/- 10 degree | |
---|
height | 143 mm | |
---|
width | 72 mm | |
---|
depth | 102,2 mm | |
---|
net weight | 0,7 kg | |
---|
specific application | Commercial equipment | |
---|
Variable speed drive application selection | Mixer Commercial equipmentOther application Commercial equipmentIroning Textile | |
---|
motor starter type | Variable speed drive | |
---|